Differences

This shows you the differences between two versions of the page.

--- network_protocol_programming_lab:change_frequency [2020/05/18 08:57] – rathke
+++ network_protocol_programming_lab:change_frequency [2021/04/19 12:40] (current) – [Tasks] rathke
@@ Line 1: / Line 1: @@
 ====== Exercise: Changing the frequency ======
-It is obvious, that changing the RF frequency is a fundamental requirement of frequency hopping systems. Programming the RF frequency is done according chapter 9.1.2 of [[http://www.ti.com/lit/ug/swru346b/swru346b.pdf?ts=1588225642109|CC1200 Users Guide]].
+It is obvious, that changing the RF frequency is a fundamental requirement of frequency hopping systems. Therefor programming the RF frequency is the aim of this exercise. Programming the RF frequency is done according chapter 9.1.2 of [[http://www.ti.com/lit/ug/swru346b/swru346b.pdf?ts=1588225642109|CC1200 Users Guide]].
-In detail, the HF $f_{VCO}$ frequency is computed by:
+In detail, the HF $f_{RF}$ frequency is computed by:
-$$ f_{RF}=\frac{f_{VCO}}{"LO\ Divider} $$
+$$ f_{RF}=\frac{f_{VCO}}{LO\ Divider} $$
-where
+where $f_{VCO}$ is the frequency of the "Voltage Controlled Oscillator (VCO)" and will be computed by
 $$ f_{VCO} =  \frac{FREQ}{2^{16}} . f_{XOSC} + \frac{FREQOFF}{2^{18}} . f_{XOSC}$$
-In this two equations $f_{XOSC}$ is the crystal frequency of the TI boards and equal to $40 MHz$. ''LO Divider" determines the frequency band of the CC1200 and will be programmed by the ''FSD_BANDSELECT'' part of the "Frequency Synthesizer Configuration" register (''FS_CFG'' register).
+In this two equations $f_{XOSC}$ is the crystal frequency of the TI boards and equals to $40 MHz$. ''LO Divider'' determines the frequency band of the CC1200 and can be obtained in the ''FSD_BANDSELECT'' part of the "Frequency Synthesizer Configuration" register (''FS_CFG'' register).
+FREQ is the 24 bit  VCO frequency and computed by the FREQ0 (bits 16-23 of VCO frequency), FREQ1 (bits 8-16 of VCO frequency) and FREQ2 (bits 0-7 of VCO frequency) registers. FEQOFF is intended for fine tuning the RF frequency caused by tolerances of the crystal and can be neglected.
+===== Requirements  =====
+This task requires
+  * a ready BeagleBone Black equipped with the CC1200.
+  * 4C attached to a second BeagleBone Black equipped with the CC1200.
+===== Tasks  =====
+  * the programming is done by reusing the source files of lesson [[network_protocol_programming_lab:15.3_2_exercise|2. Exercise: Packet Reception]]. Make a copy of the files.
+  * Change the symbol rate to 1.2 kBaud and the preamble count to 6 bytes. If necessary reexport the register value from 4C.
+  * Read chapter 9.12 ff. about programming the RF frequency in the [[http://www.ti.com/lit/ug/swru346b/swru346b.pdf?ts=1588225642109|CC1200 Users Guide]] and implement it.
+  * you should implement a function for programming the frequency and printing the current programmed frequency.
+  * for testing compare your computed values of the FREQ registers with SmartRF Studio.
+  * In your program, set RF to an arbitrary value (e.g. 851 MHz) within the supported frequency band of CC1200.
+  * In SmartRF Studio also change the symbol rate to 1.2 kBaud and the preamble count to 6 Bytes.
+  * Bring 4C in “TX Packet Mode" using the default frequency (858MHz).
+  * start the transmitter. At the receiver, the BeagleBone Black, you should now receive **NO** packet.
+  * Now, stop the transmitter and change the frequency to your selected frequency.
+  * Now, you should be able to receive the packets.
+===== Hints  =====
+  * take care on rounding errors. E.g. the frequency should be 868 MHz and not 867.5 MHz.